Car Key Button Repair

A damaged car key button is frustrating. It is possible to call an emergency locksmith service or purchase a replacement remote.

You could be able to save money by fixing your old key fob rather than replacing it. This is especially true if an old switch or damaged contacts are the reason for the problem.

Battery

If the buttons on your key fob do not respond when you pressing them, it could indicate that the battery has failed or is nearing its end of life. Fortunately replacing the battery is a simple task that can be done on your own instead of hiring a locksmith to take care of it.

First look for the battery compartment. This is usually found on the backside of the key fob. It may be hidden behind an open cover that slides out or an access point that opens when you push the button. Once the compartment has been opened then look for the small button-cell battery. It is usually shaped like an oblong coin and is has a plus and minus sign. Remove the old battery and replace it with a brand new one. Make sure the plus and the minus symbols are properly aligned.

Close the compartment and snap together the two halves of your key fob. Before closing the door key repair near me, align and snap the components in the correct position. To verify whether the buttons function properly, press any of them.

If the remote key fob you have purchased stops working even after you replace the battery, it may be experiencing other issues that require a different kind of repair car key remote. Damage to the physical structure caused by dropping the fob in a puddle, for instance may cause it to stop functioning altogether. Or, it could be suffering from an electrical issue within the device or may need to be deprogrammed by a dealer or locksmith. Take a look at these other car troubleshooting tips to see whether your key fob may be experiencing a different issue.

Switches

Depending on the year and model, there are a variety of types of switches in the keyfob of your car. The older style key is equipped with an electronic chip that is visible inside the case. The latest keys operate by transmitting signals to your car. The buttons on a key may be worn out or damaged due to normal use, regardless of the type. They become hard to press or ineffective. If you press the button with force it can cause further damage. It may also prevent the key from functioning in the future.

If your key doesn't seem to be working, you should first try changing the battery. If it doesn't work, you may have to clean your key fob or re-adjust its switches. These tiny electronic switches are more susceptible than larger parts of the key to break since they are constantly tossed about.

The switches are rubber-like, and they're coated with an electricity conducting film that is prone to wear out over time. Fortunately, they are also a small part that is easy to replace. The old ones are soldered onto the circuit board, so you will need to carefully remove them without causing any damage to anything else. Then you can put the new ones in and reassemble your key fob.

Avoid using your car key immobiliser repair key fob for more than two hours at a time and do not leave it open. If you don't use your key, store it in a secure place.

If you've tried cleaning your key fob and replacing the battery, and the problem persists, it may be the right time to seek out a locksmith. A professional locksmith can check the frequency of your key repair shop near me to determine whether your car is able to communicate. They can also open and replace microswitches, change cases, and much more.

Outer Case

If the buttons don't move freely up and down the case, they could get stuck or break. If cleaning the case with rubbing alcohol and a cotton swab fails to work, it might be necessary to take off the case. If the contacts where the buttons touch don't fit well or are worn out, adjusting them may be the only option to fix the problem.

Certain keys have buttons made of rubber that wear away over time. The rubber expands and nails pierce it and the buttons can become difficult to press. In this scenario the key may fail and it's time replace the case or button. This repair involves disassembling your remote, looking for the switch on the board, then heating the solder and carefully remove them. The circuit board is then soldered with new buttons. The case can be reassembled, and the horseshoe key blade piece can be attached. The new buttons must be snugly fitted into the case in order to keep them from falling out.

Inner Case

Since your key fob is likely to be tossed around and could occasionally be pressed by accident and the buttons within can become stuck or broken over time. Using metal tape and a hole punch you can solve this issue when your car is not at home and the key fob isn't working and you are unable to open the doors, but not to start the engine. This simple fix can enable you to safely get back to your car key fob repairs and finish your trip.