Car Key Button Repair

A broken car key button can be a source of frustration. It is possible to call a 24-hour Locksmith Service or purchase a replacement remote.

You may be able save money by repairing your old key fob rather than replacing it. This is particularly true if the switch is worn out or has faulty contacts are at the root of the problem.

Battery

If the buttons on the key fob aren't responding to pressing it, this could be a clear sign that the battery is dead or nearing the end of its life. It's easy to replace the battery on your own, rather than paying for a locksmith or dealership.

First look for the battery compartment. It is usually located on the back of the key fob. It may be hidden behind a slide-out cover or an access point that opens when you push the button. After the compartment is exposed you can look for the tiny button-cell battery. It's usually shaped like the shape of a coin and is marked with an plus and minus symbol. Remove the battery from the old one and insert a new one in its place, making sure that the plus and minus marks are properly aligned.

Close the compartment and snap the two parts of your key fob. Before closing the door make sure to align and snap the pieces in place. To test that the buttons function correctly you can press any one of them.

If your Remote Car Key Repairs key fob ceases functioning even after replacing the battery, it may be experiencing other issues that require a different type of repair. Physical damage caused by dropping the device in a puddle, for example may cause it to stop working altogether. It could also be a problem with the internal electrical system, or it may need to be deprogrammed. Also, take a look at these common auto troubleshooting techniques to determine whether your key fob may be suffering from a different issue.

Switches

There are a variety of switches found in the car key repair company key fob, according to the year and model. The older type of key usually has a separate chip which is visible inside the case, whereas newer keys are more advanced and function by sending signals to the car. The buttons on a key can be damaged or worn out through regular use, irrespective of the model. The result is they become difficult to press, or even unresponsive. If you try to press the button too hard, it can cause further damage, and could even prevent the key from starting your vehicle in the future.

If your key doesn't appear to be working, you should first try changing the battery. If this doesn't work, you may have to clean the key fob or re-adjust its switches. Because these tiny electronic switches are constantly getting jostled around and tangled, they are more likely to wear out than larger components of your key.

The switches are rubber-like and they're coated with an electric conductor film that can wear down over time. Fortunately, they're a small part that is inexpensive to replace. The older ones are soldered to the circuit board, and you'll have to take care to remove them without damaging anything else. Then you can solder the new ones in and reassemble your key fob.

Do not use your car keys repair key fob for more than an hour at a time, and don't leave it out in the open. Also, try to locate a safe place to keep your key in when you're not using it.

If the issue continues to persist after you have cleaned your key fob replaced the battery and tried to clean it, then you may need to talk to a locksmith. A professional locksmith can test the frequency of your key to see whether it's still able communicate with your vehicle. They can also open and replace micro switches, alter cases and more.

Outer Case

If the buttons don't move freely up and down in the case, they may become stuck or break. If cleaning the case with rubbing alcohol and a cotton swab fails to work, it might be necessary to take off the case. If the contact points where the buttons touch don't fit well or are worn out, adjusting them might be the only solution to fix the issue.

Some keys use buttons made of rubber, which wear away over time. The rubber expands and nails pierce it and the buttons can become difficult to press. In this case, the key may fail and it's time to replace the case or the buttons. This repair involves removing the remote, locating the buttons on the circuit board, and then heating the solder before carefully removing them. The circuit board is soldered with new buttons. The case is then reassembled and the horse shoe key blade piece is attached. The new buttons must be securely fitted into the case to keep them from falling out.

Inner Case

Since your key fob is prone to get jostled around and may occasionally be pressed by accident, the buttons inside can get damaged or stuck over time. Using metal tape and a hole-punch, you can often quickly fix this problem in the event that your vehicle isn't at home and the key fob isn't working and allows you to open the doors, but not start the engine. This simple fix can allow you to return safely to your vehicle and complete your journey.