How to Replace a kia car key replacement Sportage Replacement Key

For many Kia models the key comes with a keyless entry system built-in. This key usually resembles the remote control and can be exchanged with a brand new one from an lost kia key fob dealer or a locksmith.

Key fobs may stop working for several reasons, including batteries that are dead worn buttons or buttons, water damage, signal interference and a malfunctioning receiver module. Here are some helpful tips to help you get your Kia sportage replacement key working for good.

How to replace the remote key or smart key?

The battery inside your Kia's smart key will eventually require to be replaced, regardless of whether it's a remote key or a push-to-start one, or a regular key that does not contain transponder. This is particularly the case if your car shows a message that states the smart or remote keys aren't powered.

Luckily, this is a relatively simple process. In order to replace the battery of the key fob take out the mechanical key from the slit at the back of the key fob. Then remove the cover. A small screw is found inside the key fob to keep the battery in the correct position. Take out the old battery by unwinding the screw with the help of a small screwdriver. Then, insert the new and close the hole in the key fob.

Once the key fob has a fresh battery and you've tested it, press the lock and unlock buttons. If the doors unlock and lock according to your expectations, then you're all set! You can now use your Kia's hands-free lock/unlock feature whenever your fingers get chilly or you have to go on errands around Brandon.

Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a programing machine that is available only to the locksmith for cars or dealer. Other keys (non-transponder metal keys) do not require programming. If you want to change the programming of your key, you'll need note the key code number on the tag for the key code.

How to replace the battery

If your Kia key fob isn't responding when you press the lock or unlock button on the fob, it is a clear indication that the battery should be replaced. A battery that is not functioning properly can cause other issues, like the check engine light appearing or the engine not turning properly. Fortunately, replacing the key fob battery is a simple DIY project that requires only the most basic tools.

Before starting the process, make sure that your vehicle is off and that all doors are shut. Locate the small metal or plastic piece on the bottom of your key fob and move it until a metal key slips out. You can then insert the key in the handle of the door for the driver to open your car.

To replace the battery on the key fob, take off the cover on the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and orient the new one so that the "+" positive side faces you, and the "-" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into position and avoid excessive force to avoid bending or damaging the contacts made of metal.

Once the new battery is installed then turn the key fob off and on in the ignition repeatedly until the door locks cycle. You can then test your Kia's keys fob again to make sure it's working as intended.

How to replace the smart key

You may have either the standard keyfob or Smart Key, based on the model of Kia Sportage. The difference between them is that the smart key comes with a small mechanical key blade that is hidden inside, while the standard fob doesn't. Both key fobs come with a battery that will eventually require changing. Luckily, this is a fairly simple process that will take about two minutes.

Before you start it is important to make sure that you are on a flat surface with sufficient lighting and that your kia keys replacement is off. Also, remember that there are tiny parts inside the fob that could fall out if not vigilant.

The small release button is located on the lower backside. It will be either a circular silver button or a rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened and you are able to take off the old battery and replace it. The new battery is the CR-2032, and it can be bought on the internet or at your local auto parts shop. Once you're done it should be possible to lock or unlock your car with your key fob even if your engine isn't running!

How to replace a mechanical key

The Kia keyfob is an excellent convenience that lets us lock or unlock our Car Key Cutting And Programming Specialist by pressing a button. Like any other device, it can have problems occasionally. There are ways to resolve these issues and keep your key fobs in good working order for a long time.

A dead or drained battery is one of the most frequently encountered issues. This could cause your device to stop working or work intermittently. If this is the issue you should replace the battery an entirely new battery.

If this doesn't solve the issue, try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not to damage internal components, or scratch the plastic. After opening, carefully remove the battery that was removed and replace it with a brand new one.

Once the new battery is in, shut and open the doors using the mechanical key (every kia picanto key fob replacement fob has an emergency mechanical key that can fit into the slot). Test the key fob and ensure that it's working properly. If the fob still not working, contact an authorized locksmith or dealer to help resolve the problem. Make sure they cut you an emergency key that works for all trunk and door cylinders in order to avoid lockouts in the future.