Replacing Lock on uPVC Door

If you're looking to change the lock on your door made of upvc, you will first need to remove the existing handle and screw holes. This is usually simple to do.

Then, find the screw that is inserted into the lock barrel. This is typically a different color than the other screws, and is situated on the outside of the faceplate of the lock.

Remove the Cylinder

The first step in changing a lock on your upvc door is to remove the existing lock cylinder from the door. This is a simple process that can take about 30 minutes. All you require is a small screwdriver. You will need to find the Euro fixing screw for cylinders, which is usually in the edging on the inside of the door, next to the lock cylinder. The screw is typically colored differently from the rest of the screws and should be easy to spot. Take the screw off and store it in a safe location.

After the cylinder has been removed, you can begin working on the removal of the handle. To do this, open the door so you have full access to the inside edge of the door, as well as the side of the faceplate of the lock.

Begin by using a screwdriver to remove the screw that connects the handle to the door. Once the screw is removed you should be in a position to pull the handle towards you, and the rest of the mechanism out of the door.

If you're having difficulty taking the handle off of the door frame, you might need to remove it. You can use a screwdriver or drill to remove the handle. Be careful not to strip or cross-thread it.

If you are about to replace your cylinder, make sure that it is the right size for the door you have. Cylinders are measured according to two measurements: (a) the distance from the middle of the Fixing Screw hole to the bottom of the cylinder and (b) the distance between the keyhole and the edge of the lock plate.

Remove the Handle

The good news is, the moment your upvc handle starts to become stiff, floppy, or loose, it's an easy problem to solve. The multipoint lock cylinder or other internal components inside the door, between the handle and frame, are often the cause. Weather conditions, heavy usage or ageing can cause upvc window locks repair to wear. This can lead to problems with the locking and closing mechanisms of the door.

If the cylinder has been worn, it may be difficult to turn the key, and the lock could be stiff, which could cause the handle to loosen. The cylinder can be repaired, and is a straightforward process. It is possible to do it yourself, but some understanding of how the mechanism works is required. You'll need to take off the handle in order to replace the cylinder.

To accomplish this, you'll require an screwdriver and tape measure. You must know the size of the cylinder you have, because it will allow you in locating an appropriate replacement locks for double glazed windows. The cylinder is the element that allows you to lock your upvc window replacement lock door. Therefore, it is essential to make sure you purchase an identical replacement size.

To remove the old cylinder, you will have to remove the screws which hold it in place. Be careful not to remove the screws, as this can make it very difficult to remove them in the future. After the screws have been removed, the cylinder should be easy to remove.

Take off the Lock Barrel

uPVC is a very strong material, designed to keep you and your family secure. They are available in a variety of styles and colors that will fit any style. These doors are also maintenance-free and energy efficient. However, they do have some disadvantages. Over time the barrel or locking point lock may fail and will require replacement. It's a simple process however, you must be aware of a few things prior to beginning.

You'll need to take off the door handle in order to reach the screw that holds the lock cylinder. The screw is usually different from the other screws, and is located near the keyhole on the edge of your door. Take the screw off and store it safely. Then, carefully move the inside and outside door handles. Do not rush to do this, as it could damage the uPVC.

After you have removed the handles, use a screwdriver to disconnect the screws that are holding them to the frame of the door. This will allow you to gain access to the support pins that are holding the cylinder in place. You can then move the cylinder in order to see if this will loosen it. Once it comes loose move it toward you, then pull it away from the socket.

After you have removed the old lock cylinder it is important to replace with a new one that is anti-snap and anti-bump. It is best to have an expert locksmith handle this for you, but you can do it yourself using the appropriate tools. This is a relatively easy task that will take five minutes to complete.

Install the New Cylinder

A upvc lock may be damaged or broken in a number of different ways. For example the cylinder could have become damaged or isn't working as it should. Whatever the reason for changing your repair upvc window lock double glazing window lock repairs, it is important that you choose the correct size replacement. If the wrong lock is installed, your upvc doors may be more vulnerable to the 'lock snapping technique' which is responsible for 25% of burglaries.

To avoid this, it is essential that the correct cylinder is used and the procedure for doing it is a breeze and takes just five minutes. You will require a screwdriver to take off the screws that are attached to the faceplate on the handle and the cylinder, but once this is done it's a simple task to replace them.

Before you get started ensure that the handle is opened and that you have full access to the inside edge of the door and the side of the handle faceplate that holds the lock cylinder. This will enable you to easily remove the lock cylinder from the handle without the need to move it or expose the internal parts of the frame.

The next step is to remove the old cylinder and measure it, you must determine the length of the cylinder and the diameter of the cam that moves to lock and unlock the door. This will help you locate a replacement that is similar in size or smaller, which is the most crucial aspect of the whole process. The cylinder should be flush with the handle, and not protrude more than 5mm from it.

Install the Handle

It is not uncommon for a door lock made of upvc to stop working and this could be caused by something breaking inside the case that controls the bolts that retract into the keep or strike plate. Most of the time, this issue can be solved by making an Allan key adjustment beneath the hinges of the door but often this may put excessive pressure on the parts inside the centre case, and it is recommended to seek the help of a professional.

During the changing process it is essential to have quick and easy access to both sides of the handle, as well as having the right tools. It is also recommended to prop the door open so that it doesn't close during this process.

The first step is to loosen the screws that keep the handle together using the help of a screwdriver. After the screws are loose then you can remove the handle. After the cylinder and handle have been removed, it's now time to install the new handle. Make sure the new handle is compatible with your existing cylinder center and the cylinder. Check the length of the spindle on the lever you have currently to determine this. Also ensure that the screw fixing centres on the handle match the screw fixing centres on your current cylindrical cylinder and hole centre.

Replacement handles from Fab & Fixed are available in various designs and are made to last. These handles are perfect for those who wish to upgrade their upvc handle and enhance security in their home. A good handle will ensure that your house is secure and safe and won't be easy for burglars to break into.