How to Replace a kia rio key replacement sportage replacement key - Kingranks's website -

The key on many Kia models comes with a keyless entry system built into. The key functions like a remote control and can be exchanged by an 2014 kia sportage key fob dealer.

Key fobs may stop working for a variety of reasons, such as the battery of the coin is dead, worn buttons signals, signal interference, water damage and a malfunctioning receiver module. Here are some guidelines on how to get your Kia Sportage replacement key working again.

How do you replace a smartkey or remote key?

If your Kia is equipped with an intelligent key, remote key, push to start key, or a standard non-transponder key made of metal, the battery in these keys will eventually require replacement. This is especially relevant if your car displays a message telling that the smart or remote key is not powered by the battery.

It's a simple process. To replace the battery on the keyfob, remove your mechanical key from the slit that is located at the back of the fob. Then, pull the cover open. Inside the key fob will be a small screw that holds the battery in the correct position. By using a small screwdriver remove the screw and pull out the battery that was in place. Then insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock in the same way, you're set! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become cold or you need to run errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder metal keys), do not need programming. If your key requires to be programmed again, you will need to be aware of the key code number that is stamped on the tag of the key code and keep it in a safe location.

How do you replace a battery?

If the Kia key fob does not respond to pressing the lock/unlock button, it is likely that the battery is low. A battery that is not functioning properly could cause other issues such as the check engine light flashing on or delayed cranking of the engine. Fortunately, replacing the battery on the key fob is a fairly simple DIY task that requires only some basic tools.

Before starting the process before beginning the process, ensure that your vehicle is turned off and all doors are closed. Find the small metal or a plastic piece on the bottom of the key fob. Press it until the metal key falls out. Then, you can insert the key into the driver's door handle to unlock your car.

To replace the key fob battery, remove the cover at the rear and use a plastic pry bar tool to loosen the latch holding the black negative battery cable. Remove the old battery, and then place the new battery to ensure that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.

After the new battery has been installed and the key fob is turned on, turn it off and then turn it on in the ignition for a few times until the door locks. You can then test your kia spare key cost's keys fob again to confirm that it is working correctly.

How do you replace the smart key

There is a possibility of having an ordinary keyfob or Smart Key based on the model of Kia Sportage. The smart key has an embedded mechanical key blade, while the standard key fob does not. Both types of key fobs have a battery inside them that will eventually need to be replaced. This is a straightforward process which takes just two minutes.

Make sure you turn off your Kia and sit on a flat, well-lit surface before you begin. Also, keep in mind that there are tiny components inside the fob which could be removed if not careful.

The small release button is located on the lower backside. It's either an oval or circular slot. Once you press this mechanical key blade, it will pop out and you can then open the key fob.

Once you have the key fob open then you can remove the old battery, and replace it. The new battery is a one called CR-2032 and can be bought through the internet or at a local auto parts store. When you are done you should be able to lock or unlock your vehicle with your key fob even if the engine isn't running!

How do I replace a mechanical key

The Kia keyfob is a wonderful convenience, allowing us to lock or unlock our car simply by pressing a button. Like any other device that is used, the kia key fob replacement cost key fob might have issues. There are methods to resolve these issues and ensure that our key fobs are in good condition for the long run.

A dead or drained battery is among the most frequently encountered issues. This can cause your fob to stop working or work intermittently. If this is the case you should replace the battery a new one.

If this doesn't fix the issue Try using a standard flathead screwdriver to wedge open the casing of the fob's plastic. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed then replace it with a brand new battery.

When the new battery is installed, close and unlock the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that can fit into the slot). Test the key fob to verify that it's working as intended. Contact a dealer, or a locksmith to resolve the problem in the event that the key fob is not working. To avoid a lockout in the future ensure you have an emergency key that can be able to work with all door and trunk cylinders.