How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with a keyless entry system built in. The key is usually akin to a remote control and can be replaced with a fresh one from an Kia dealer or locksmith.

Key fobs might stop working due to a variety of reasons, including the battery of the coin is dead worn buttons or buttons, signal interference, Reprogram water damage and a damaged receiver module. Here are some guidelines on how to get your kia flip key repair Sportage replacement key to function again.

How do you replace a remote key or smartkey

If your Kia is equipped with an intelligent key, remote key, push to start key, or a standard non-transponder key made of metal, the battery in these keys will eventually need replacement. This is particularly when the car displays a message telling that the remote or smart key has low battery power.

It's a relatively simple process. To replace the battery of the keyfob remove your mechanical key from the slit at the back of the fob. Then, pry the cover off. A small screw will be found inside the key fob that holds the battery in the correct position. By using a small screwdriver loosen the screw and remove the old battery. Install the new battery and close the cut on the key fob.

When the key fob is equipped with a fresh battery check it by pressing the lock and unlock buttons. If the doors lock and unlock in the same way, you're in good shape! You can now utilize the hands-free feature to lock and unlock your Kia when your fingers get cold or when you need to go on errands around Brandon.

Note: Certain key fobs (transponder chip or smart keys) may require their programming completed. This requires a special programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of metal) do not require programming. If your key has to be reprogrammed, you must be aware of the key code number printed on the tag of the key code and record it in a safe location.

How to replace a battery

If the Kia key fob does not respond to pressing the lock/unlock button, it's likely that the battery is depleted. A low battery may also cause other issues, such as the check engine light flashing on or a delay in cranking the engine. Fortunately, replacing the key fob battery is a simple DIY project that requires just a few basic tools.

Before you begin ensure that your vehicle is turned off and all doors are shut. Find the small metal or a plastic piece on the bottom of the key fob. Jiggle it until the metal key is released. The key can be put into the driver door handle to unlock your car.

To replace the battery in the key fob remove the cover on the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and align the new one in a way that the "+" positive side faces you and the "-" negative side is facing towards the fob's electronic contacts. Push the new CR2032 battery straight into place with care to avoid using too much force to avoid bending or damaging the contacts of the metal.

Once the new battery has been installed then turn the key fob off and then turn it on in the ignition repeatedly until the door locks cycle. You can then test your Kia's key for kia sportage fob once more to ensure it's functioning properly.

How to replace the smart key

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The difference is that the smart fob has tiny mechanical key blade hidden within it, whereas the standard key fob does not. Both key fobs contain batteries that eventually need to be changed. Fortunately, it's an easy process that takes just two minutes.

Make sure to shut off your kia sorento locked keys in car and sit on a flat well-lit and well-lit area before you begin. Also, remember that there are tiny components inside the fob that can fall out if you are not vigilant.

The release button for the small size is located on the lower backside. This will be either a circular button or a rectangular slot. After pressing this button the mechanical key blade will be released and you will be able to open the key fob.

After the key fob has been opened, take out the old battery. The new battery is a CR-2032 that can be bought online or from your local auto parts store. Once you're done, you should be able to lock or unlock your car using your key fob, even if the engine isn't running!

How do you replace a broken mechanical key

The Kia key fob is a fantastic option that lets us lock and unlock our car with the touch of one button. Like any other device it will encounter issues from time to time. Luckily, there are ways to solve these issues and keep our key fobs in good working order for the long run.

One of the most frequent problems is a dead or dead battery. This can cause your fob to stop working or work intermittently. If this happens try replacing the battery with a fresh new one.

If this doesn't solve the problem, use a flathead screwdriver standard to push the fob's plastic casing open. Be careful not to harm any internal components or scratch the plastic. Once the battery is removed then replace it with a new one.

Close and open the door using the mechanical key. (Every Kia fob comes with an emergency mechanical key that fits into the slot). Test the key fob and make sure it is working properly. Contact a dealer, or a locksmith to resolve the problem if the fob is still not working. To avoid locking outs in the future, make sure you get an emergency key that can work on all trunk and door cylinders.